Владимир1974 из "опасного" добавлена команда получить путь к папке из которой запущена оболочка.

Я один не понимаю, для чего держать на машине с программаторами антивирус? Или кто-то думает, что в считанном hex'е антивирус что-то сможет исправить?
P.S. Это конечно оффтоп, но, люди, уже имейте головы.

У всех есть отдельные машины под программаторы ? У меня один рабочий комп, на нем и висят программаторы, думаю что и у большинства также. Извиняюсь за оффтоп, просто в тему

Может этот кусок кода можно написать по-другому?

это происки конкурентов
у них недавно были те же проблемы с антивирусами

_________________
ремонт ноутбуков, планшетов в Одессе
продажа паяльных станций Термопро ик-650
и расходных материалов для пайки и ремонта

Проблема не антивирусе, а в коде Сергея, который нужно поправить. У меня была похожая проблема в моей программе, там проверка повторялась несколько раз, и антивирусу это не нравилось, я эту проблему решил.

Avast прислали сообщение, что файл чист. Теперь версия 4.93 нормально запускается.

Владимир1974
а они не сказали, что им не понравилось

Lenovo G50-70 20351 ACLU1 ACLU2 NM A271 REV 1.0
мульт IT8586E

ошибка при чтении
ITE мульт нам не отвечает, проверяйте соединение и настройки выводов. MB запитана? (2F)

is there no explanation for ITE reading writing in english ? im a bit confused of how to programe the nm-281 !!

im having an issue , kbc was toasted on this unit , bought new one , but once i insert power on board , it does turn on and stay dam ON ... so ITE reading or writing impossible . tryed to only give power to LE1 on the KBC , but even like that a bloody 1 amp consume and no way to go as well (altough kbc not hot , its quite ok .. ) even like that tryed a second KBC , exact same issue .
any way of doing it ?

and also no english on ITE programming ?

TE ìóëüò íàì íå îòâå÷àåò, ïðîâåðÿéòå ñîåäèíåíèå è íàñòðîéêè âûâîäîâ. MB çàïèòàíà? (3F)

dam i try copying whats on the error m essage , but once i past it , it stay that way

highpulse
### The current version and instructions and driver FTDI(ver. 4.93) ###
manual included

hi sergey , i noticed and donwlaoded it , instaled new version , there english allready :d nice heeh but keep saying if MB? is connected .

cheked , 3vlw ok 5 alw enable , 3valw_Ec present all power on kbc except to 3vs (3vs will be enable once S0) so there is no need of this voltage for programing. but tryed tons of times always same error .

highpulse
ITE changed? Maybe bad soldered?

hey sergey , yes ITe was replaced , with a new 8586E (same as the model had)
i achieve to one or two times to start flashing but then say lost connection to ITE .
its gives me a lot of error every attempt , (00) (01) (t001) examles of the code in the end of the error .
KBC is well soldered , even cheked on macroscope , all pins well soldered , indeed my daily job , but even like that i spent time on the macroscope and all well soldered.
really don't know what else . !!!
2 new ITE making same , its kinda weird , both were brand new .

@highpulse:
I encountered same problem as you. I resolved the problem with isopropyl alcohol. I dipped whole board in new batch of alcohol into ultrasonic bath, and also cleaned all cables and connectors thoroughly with isopropyl. After that, everything works fine.

Just to be clear: Wash the programmer from Sergey in ultrasonic bath.

ok mate , i can try that , let you know ASAP

or output connector

well nothing !!! same isssue , im in the near moment of destroying both motherboard and programmer , really annoying ,


i even tryed to make things this way now , connect programmer to laptop and wioth ribbon cable to motherboard , choose de nm-281 board , and press apply , it reads and give the followinng info

once i press APPLY -
current time 12:51:28
Number of VCOM ports found on the machine: 1
Programmer FW version -> ITE 19_06_2016
Communication with programmer installed.
Send the settings for MB.
All settings sent.

ok after that i press chek , chek connections -
Check connection ...
Number of VCOM ports found on the machine: 1
Programmer FW version -> ITE 19_06_2016
Communication with programmer installed.
The programmer is found and ready to go.

Now, as soon as possible, connect the adapter (5 seconds) !
Received ITE ID -> 8586 rev -> 02

attention not always it can say it received ITE ID ,. major part of warning are related that there is no connection to board or no power on it ...


after pressing chek connections , if i try to WRITE -

ber of VCOM ports found on the machine: 1
Programmer FW version -> ITE 19_06_2016
Communication with programmer installed.
Current time 12:53:54
Data file: C:\Users\rbga power\Downloads\NM-A281.bin
Writing starts ...
INIT ...
ITE we do not respond, check the connection and settings. MB powered? (T001)
Current time 12:53:55


so resuming im getting MADDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD



help guys

like i mentioned , programmed a ton of ENE's and no problems , all working until now .

highpulse

Write what is written on the chip itself?
IT8586C XA ????


In this case, should have
Received ITE ID -> 8586 rev -> 04
Check the GROUND contact, сlean the contacts of FFC cables and sockets ...

rev 0 -> A
rev 1 -> B
rev 2 -> C
rev 3 -> D
rev 4 -> E
rev 5 -> F
...

ITE 8586E
CXS

ground usb contact is ok ,
im using programmer directly with ribon cable 30 pins . cables all cleaned , your programmer was on US Cleaner as well , same issue , cleaned all ribbon cables , same issue

highpulse
Have you tried two scenarios when you connect the power to the motherboard?

first
1 APPLY
2 Connect power to MB and wait 3 sec.
3 Check answer
4 READ

two
1 APPLY
2 Connect power to MB and quickly Check answer
3 READ

PS Why do you put the other revision IT8586?
Сhip UC3 (W25Q64F) on the MB present ?

i replaced the ITE because it was damaged , shorted , making 3vlaw to crash . cheking carefully noticed was 3alw_ec , once kbc removed no more short , after replacing new one , all good , except cant programing .


so second option , was gave me at least possible to read around 3% then error
Number of VCOM ports found on the machine: 1
Programmer FW version -> ITE 19_06_2016
Communication with programmer installed.
Current time 17:03:38
Reading start...
INIT ...
INIT complete.
READ, please wait ...
ERROR reading block ->21
Current time 17:03:45

yes bios is present , 8 mb , but its UC5

trying second method but to write , does this

Number of VCOM ports found on the machine: 1
Programmer FW version -> ITE 19_06_2016
Communication with programmer installed.
Current time 17:10:23
Data file: C:\Users\rbga power\Downloads\IT8586_128kb.bin
Writing starts ...
INIT ...
INIT complete.
ERASE complete.
File loaded to buffer.
The number of bytes equal to the value of FFh -> 72239
WRITE, please wait ...
Error writing to flash or lost contact with ITE
Current time 17:10:27

start running the bottom progress bar many times , and the upper progress bar is stoped . then the bottom stop at 86%

highpulse
The problem on your motherboard. Check the power supply, can be voltage ripple.
A week later, I will have this motherboard and I can advise something.

Новое видео канала HamRadio Tag (Алексей Ж.)
[BBvideo 425,350]http://mx.youtube.com/watch?v=74XSDsesz4A[/BBvideo]

Никак не могу победить IT8587E FXA .Программатор не хочет их стирать. Записывает нормально поверх старой прошивки, но не стирает, соответственно получается "каша".Пробовал три мульта , толку нет.

Kireev версия оболочки какая?
PS Была такая проблема, но давно исправлено. На первой странице этой темы все найдете и скачаете.