U-Boot SPL 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)

config ddr_pll_config()++

config ddr_pll_config()--

nand_init+++++

nand_init-----

Lcd_Init()++

SetUpLCD()++

SetUpLCD()--

len=768052, height=480, width=800

Logo from nandflash: base=0x81000000; end=0x810bb81f; end-base=0xbb81f; rwsize=0xbb820; r=0x0

Lcd_Init()--





U-Boot 2013.01.01-svn29730 (Mar 27 2017 - 19:02:34)



I2C:   ready

DRAM:  128 MiB

NAND:  256 MiB

MMC:   OMAP SD/MMC: 0, OMAP SD/MMC: 1

Using default environment



set_default_env::7864

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Peripheral mode controller at 47401000 using PIO, IRQ 0

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

USB Host mode controller at 47401800 using PIO, IRQ 0

Net:   <ethaddr> not set. Validating first E-fuse MAC

cpsw

Hit any key to stop autoboot

(Re)start USB...

USB0:   lowlevel init failed

USB error: all controllers failed lowlevel init

Download Linux from USB to Nandflash...

** Bad device usb 0 **

** Bad device usb 0 **

** Bad device usb 0 **

** Bad device usb 0 **

Booting from nand ...



NAND read: device 0 offset 0x3080000, size 0x300000

 3145728 bytes read: OK

## Booting kernel from Legacy Image at 80200000 ...

   Image Name:   Linux-3.2.0+

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    2157768 Bytes = 2.1 MiB

   Load Address: 80008000

   Entry Point:  80008000

   Verifying Checksum ... OK

   Loading Kernel Image ... OK

OK



Starting kernel ...



Uncompressing Linux... done, booting the kernel.


init started: BusyBox v1.13.2 (2012-04-08 17:28:57 CDT)


starting pid 519, tty '': '/etc/init.d/rcS'

rS in

/etc/init.d/rcS: line 15: setterm: not found


starting pid 536, tty '/dev/ttyO0': '-/bin/sh'



Processing /etc/profile... Done



/ # check_and_upgrade:starting...

mount_fs: rw,sync,ubi1_0,/usr/bin/siglent/usr

ubi1_0unattached

attach_ubi:datafs

attach_ubi:11

UBI device number 1, total 812 LEBs (103104512 bytes, 98.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)

MOUNT_DIR_NAME = /usr/bin/siglent/usr

TEST_RESTURN =

is_fs_mounted 0 ---

is_need_upgrade

is_need_upgrade:not need upgrade

check_and_upgrade:end...

++mount_check_copy_appdata: starting

mount_fs: ro,sync,ubi2_0,/usr/bin/siglent/firmdata0

ubi2_0unattached

attach_ubi:firmdata0

attach_ubi:9

UBI device number 2, total 400 LEBs (50790400 bytes, 48.4 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)

MOUNT_DIR_NAME = /usr/bin/siglent/firmdata0

TEST_RESTURN =

is_fs_mounted 0 ---

--mount_check_copy_appdata: ending

Load Fpga Success!


ECC failed: 0

ECC corrected: 0

Number of bad blocks: 0

Number of bbt blocks: 0

Block size 131072, page size 2048, OOB size 64

Dumping data starting at 0x00000000 and ending at 0x00010000...


Erasing 128 Kibyte @ 0 --  0 % complete
Erasing 128 Kibyte @ 20000 -- 50 % complete
Erasing 128 Kibyte @ 20000 -- 100 % complete

The Help file load OK!!


I0101 00:00:10.817821   534 module.cpp:568] ---------------------------------------------------------------------------------------

I0101 00:00:10.840653   534 module.cpp:569]                     Creat Log

-----------------------------------------------------------------------------------------------------------------------------------

 

I0101 00:00:10.870225   534 module.cpp:464] rm -f /usr/bin/siglent/usr/log/Info_19700101-000010.534

I0101 00:00:11.097768   534 module.cpp:489]

-----------------------------------------------------------------------------------------------------------------------------------


vxi11_main = 11214

init_lcd_driver()++

g_vinfo.xres = 800

g_vinfo.yres = 480

g_vinfo.bits_per_pixel = 16