hi guys is possible to have a full dump BIOS ( 8mb) of this notebook ?

thanks

very thanks dear and very greatful....

This community is very great.

hi dear ,

i have loaded this file into dediprog sf100, with manual voltage to 2.5 V.

The chipset bios are Winbond W25Q64FV and in config i have selected:

Batch Operations -> Download a whole file to chip ( without blank check) .

Miscellaneous Menu -> Vcc Option --> 2.5 V
-> Spi Clock Setting --> 12MHz

Flash Option ---> unprotect blocks automatic





but during the flash ( batch procedure) appears this message :

Warning : BLocks are protected

what is your opinion?

Thanks



Ps this is log :

2014-Apr-06 02:26:54: Welcome to DediProg SF6.0.4.30
2014-Apr-06 02:26:54: Start logging ...
2014-Apr-06 02:26:54: Checking Windows version ....
2014-Apr-06 02:26:54: Windows version: Windows 7
2014-Apr-06 02:26:54: Checking USB connnection ....
2014-Apr-06 02:26:54: USB OK.
2014-Apr-06 02:26:55: 0.798s elapsed to identify chip.
2014-Apr-06 02:26:59: Current Type: W25Q64FV
2014-Apr-06 02:26:59: VCC 3.5V is applied.
2014-Apr-06 02:27:07: Advanced settings...
2014-Apr-06 02:27:17: Advanced Settings completed.
2014-Apr-06 02:27:18: VCC 2.5V is applied.
2014-Apr-06 02:27:18: Warning: Enable auto unprotect block.
2014-Apr-06 02:27:18: Warning: Batch with erase.
2014-Apr-06 02:27:34: Loading C:\Users\user\Downloads\X551CAAS210 (1)\chip2.bin ...
2014-Apr-06 02:27:34: C:\Users\user\Downloads\X551CAAS210 (1)\chip2.bin Loaded.
2014-Apr-06 02:27:34: Operation completed.
2014-Apr-06 02:27:34: 0.758 seconds elapsed.
2014-Apr-06 02:27:47: Advanced settings...
2014-Apr-06 02:28:06: Advanced Settings canceled.
2014-Apr-06 02:28:09: Programming parameters:
2014-Apr-06 02:28:09: Source File: chip2.bin(0x800000 bytes)
2014-Apr-06 02:28:09: Target Memory Region: [0, 0x800000)
2014-Apr-06 02:28:09: Spare Memory Region: leave as being erased.
2014-Apr-06 02:28:09: Truncate-File-To-Fit-Memory Disabled.
2014-Apr-06 02:28:10: Identify Chip OK.
2014-Apr-06 02:28:10: Erasing a whole chip ...
2014-Apr-06 02:28:10: Auto unprotect block is enabled
2014-Apr-06 02:28:10: Warning: Block(s) are protected
2014-Apr-06 02:28:10: Unprotecting blocks...
2014-Apr-06 02:28:10: Error: Failed to erase a whole chip
2014-Apr-06 02:28:10: Operation completed.
2014-Apr-06 02:28:10: 0.427 seconds elapsed.

Why??? Standart Vcc is 3.2V (2.7 to 3.6V supply, see datasheet).
Or change the chip by new...

Thank you for having responded to me. I was able to enter v. 2.5 because 3.5 V does not find the chip. The mainboard Is not connected to DC brick and no power button is connected on the mobo.


The firmware of Dediprog is 5.5

On the mobo there is only the cmos battery


What is the problem ?

Hi
Tagansiti rights - Standart Vcc is 3.2V (2.7 to 3.6V supply, see datasheet).
and yet - pin 3 (Write Protect Input)

Datasheet W25Q64FV:

"3.12 Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Registers from being written. Used in conjunction with the Status Register’s Block Protect (CMP, SEC, TB, BP2, BP1 and BP0) bits and Status Register Protect (SRP) bits, a portion as small as a 4KB sector or the entire memory array can be hardware protected. The /WP pin is active low. However, when the QE bit of Status Register-2 is set for Quad I/O, the /WP pin function is not available since this pin is used for IO2. See figure 1a, 1b and 1c for the pin configuration of Quad I/O operation.
....
When /WP pin is low the Status Register locked and can not be written to.
When /WP pin is high the Status register is unlocked and can be written to after a Write Enable instruction, WEL=1."

What can I do? I do not have to connect pin3? I did not understand, thank you for your kindness

The best option to buy TL866A
http://www.autoelectric.cn/MiniPro/Index.htm

Look...

programming on the board - a bad decision.
good option for your programmer - Flash Module-SO8W(207mil) socket

Hi guys,

is possible to have a new full dump of x551ca-sx024d with lan ?

thanks

Mean you "with MAC address"?
Try to use bt.exe...

hi тагансити bt.exe not work in this computer because this has a Aptio Bios

there are another solution?

........Lay here your dump.... and specify the MAC-address, which must have...

_________________
...!!стучитесь....и вас откопают...
...!!knock.. and you will be dug up...

this is a bios

http://cjoint.com/?0DAnzlBlC7u

and mac address are :E03F49301212

Try to flash:

Use Flash Image Tool for edition MAC in future...

... ах Сергей..Сергей...не дал мне карму приподнять..

_________________
...!!стучитесь....и вас откопают...
...!!knock.. and you will be dug up...

ok, thanks and what region occur operate for insert MAc address?

ME Region => ME Debug Event Service (I think so)...

Ah very thanks тагансити.

How to insert SN and UUID ? Exist a procedure?

For UUID, I think, ME Region => Configuration => FW Update OEM ID.
For SN, I don't know, sorry...

Have you flashed the dump E03F49301212.bin?
What about MAc - is it right?
What is SN displayed at the BIOS page now?

Morning тагансити

still have not been able to work on the pc, because I was not at home these days. In these next few days we work on and I'll tell you

thanks for the kindness in the meantime

Morning тагансити

i have put the bios on winbond, but the problem are every this, no Lan Work and no SN

Hi, harsan!
Try to use bt.exe under DOS (boot from DOS first).
It should help...

Hi dear, I used bt2.exe and cant write

because is it so this aptio?

От себя добавлю.

Прошивка сверху чистая, без серийников, MAC-адреса и прочего. С ней получаем нерабочую сетевуху (код 10, запуск устройства невозможен). Чтобы все было ОК - надо перенести из родной прошивки кусок с серийниками (начинается с адреса 230000H, заканчивается предположительно по адресу 280000H).

С помощью BT.exe прописать не удалось.